El & VVS - side 342

The set consists of a panel, rail, heightener set and screws. The set must be assembled before installation.

Includes 2 x hooks to be used for lifting the panel.

The panel solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit. Installed with HighLine frame.

The heightener set to adjust the panel is included, so that the panel can be matched to the frame height.

NB: PVD-treated surface.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

PP-forminger med stikkontakt. Brukes til avløpsinstallasjoner i bygninger

Wavin BRACKETS 40MM NO LOC DEV WHITE

Lyslupe

Mushroom Toothbrush Holder

Viega 2416

Uponor 1070568 VVS-kobling Trykkreduserer

Nipple- gunmetal- G-thread

Lang brystvorte i gunmetal med R-gjenge. R: 34, L: 150 mm

Viega 2326.1

Sanpress Inox T-piece with SC-Contur- steel non-corroding- press connectors, Rp-threadComponentsEPDM sealing elements, polygond1: 15, Rp: 12, d2: 15

Viega 2326.1

Viega 2317.2

Viega 2318

Sanpress Inox T-stykke med SC-Contur- stål ikke-korrosive- trykk-koblingerKomponenterEPDM tetningselementer, VdS-sertifiseringd1: 42, d2: 35, d3: 42

Viega 2315

Sanpress Inox skyvekobling med SC-Contur- stål som ikke korroderer - trykkontakterKomponenterEPDM tetningselementerd: 42 (VdS-sertifisering)

Viega 2311

Press connector system with press connectors and pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DIN EN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-die

Viega 2311

Viega 2311.1

T-stykke - kobber - loddeforbindelse d1: 28, d2: 28, d3: 28 (kvalitetsmerke for d12-54)

T-stykke - kobber - loddeforbindelse d1: 15, d2: 12, d3: 15 (kvalitetsmerke for d12-54)

T-stykke - kobber - loddeforbindelse d1: 18, d2: 15, d3: 15 (kvalitetsmerke for d12-54)