IHC Visual Controller 3 incl. antenna. The controller is designed for use in building services, including lighting control, monitoring, alarm system and thermal management. In IHC controller gets the information from the connected signal generators worked. This can result in an on or off switch, timer function, a flasher, a dimmer signal etc., depending on the programming. To obtain function carried forwarded information to the actuators, which activate the desired appliances.

The compact RJ45 uses IDC technology for easy field assembly - connection is made without tools.The plug is compatible with all required standards. Large conductor cross sections can also be connected.The plug lives up to category 5e.

Operating tool with partially insulated shaft, blade (3.5 x 0.5) mm, short, angled, particularly suitable for 280 Series actuator and sensor terminal blocks and also for Series 260, 261, 262, 264, 280, 281, 869, 870, 880, 2002,,

IHC Control Modem SMS modem. To monitor and control the IHC input and output modules using SMS messages over the GSM network. SMS module can be used both in small systems as Stand alone, ie without an IHC controller and IHC Control systems with an IHC Controller with Viewer. The modem can also send text message by power outages. In Stand alone operation includes modem management to make thermal management based on SMS messages. So that it can be used as inexpensive system for remote control and monitoring of eg heat in the cottage.

IHC Control Alarm magnetic contactset for screeded mounting in doors and windows

Present detector flush mounted 360°, DALI, All-in-one, 230V, EnOcean

ABB KNX DALI-Gateway, Basic, 2-foldFor controlling DALI devices via ABB i-bus®. Two DALI outputs. Max. 2x64 DALI slaves (incl. emergency devices acc. EN 62386-202). Status feedback a control happens via KNX per DALI slave, group, Broadcast. Szene-, slave-, staircase-, force and block-fct.

PTM 215B enables the realization of energy harvesting wireless switches for EnOcean systems communicating based on the BLE radio standard. PTM 215B is mechanically compatible with the established PTM 21x form factor enabling quick integration into a wide range of designs.Key applications are wall-mounted or portable switches either with up to two rockers or up to four push buttons.PTM 215B provides an NFC interface according to ISO 14443 for configuration.

This motion detector is suitable for outdoor use, for example, along the driveway, on the terrace or in the garden. It is also equipped with a built-in light sensor. You aim the motion detector wherever you wish and partition the detection area using a cover mask. The Niko Home Control system supplies power to the device. Finishing colour: black

Operating tool with partially insulated shaft, blade (3.5 x 0.5) mm, short, suitable for 260, 261, 262, 264, 270, 280, 281, 869, 870 and 880 Series,

Busch-Presence detector premium KNX 6131/31-24-500 Detection range (for mounting height 2.5 m, 3 m and 4 m): circular. Seated persons Ø: max. 8 m, max. 10 m and max. 14 m. Walking persons Ø: max. 10 m, max. 12 m and max. 16 m. Visible height 23 mm. With 4 channels. For dimming/brightness of the rules to a defined value in a designated collection area. HVAC function for controlling heating and/or cooling systems and ventilation systems in the designated collection area. Detectors application with 2 power off stages. Detectors application with integrated monitoring function. Constant light controller with up to two independent channels. Constant light controller with max. 2 outputs for dimming daylight control/rules of two rooflights in the room. Integrated object room temperature controller. 10 freely programmable IR channels (blue and/or white) Incl. 5 logic channels (logic gates, gates, delay and staircase lighting) Evaluation via internal brightness sensor. Weighting of up to 2 exter

· Group or lighting scenario control is selected using switch· May be connected in parallel to obtain multiple groups/scenarios/operating points· DALI-controlled coils for fluorescent tubes and compact florescent lamps· DALI-controlled universal dimmer 65-411· DALI-controlled relay modules 36-890 and 70-980

This module is used to connect sensors with an NPN or digital contact output and safety extra-low voltage to the Niko Home Control installation, for example, twilight switches, smoke detectors, motion detectors, door intercoms and videophones, etc.

Single flush surround plate from the range Niko Intense. Finishing colour flush surround plate: Intense white.

adhesive pad softline - wireless - 1 module - silver

IHC Wireless Battery Press accessories adhesive pad Baseline 1modul.Anvendes when the battery pressure mounted on glass surfaces. Comes in a bag with 5 pieces.

For controlling DALI devices via ABB i-bus®. One DALI output. Max. 64 DALI slaves (incl. emergency devices acc. EN 62386-202). Status feedback and control happens via KNX per DALI slave, group or broadcast. Szene-, slave-, staircase-, force and block-fct.

Power supply with integrated choke and bus coupler for diagnostic function via KNX or ABB i-bus ® tool. With 30 VDC output to supply a second line in connection with a separate choke. LED Display: Bus current, status, overload, telegram and communication.

Binary DALI input device for installation in in-wall sockets4 inputs for conventional push buttons, freely configurableOperating modes: Standard, staircase or scene modeIntegrated LED to determine location of dismantled deviceIntegrated buzzer to determine location of installed deviceDIP- and HEX-switch for quick commissioning with basic functionalityFull range of functions can only be activated with other products of the product group B.E.G. LUXOMAT®net DALI LINK

· For surface mounting on ceiling· Used together with Master type 41-760· Extends the detection area to all above-named Masters· Plug & Play – no programming· Rapid and flexible installation with DALI addressable bus· Detection angle 360o or 3x120o with individual sensitivity· Protection class IP54

Used with presence detectors 41-75x, 41-76x and 41-78x DALI

IHCWireless for incorporation Input 1-4 channel. Used for installation in products to be able to send input to IHC Wireless system. The transmitter is battery operated and can be connected to up to four pressure. Both short and long pressures can is transmitted (eg. By dimming) . Continually signals from, for example. one NC contact should not be used on the transmitter. The transmitter can be used for LK Wireless stand-alone or with IHC Control.

IHC Control cabel USB-RS232 converter for communication IHC Visual 1 and PC

This switching module is used to switch six different circuits, for example, light points, socket outlets or control valves. By pushing the button, you can also control each contact manually. Using this module, you can interconnect two zero conductors, this keeps the wiring in the electricity cabinet tidy. The module is equipped with six feedback LEDs and one status LED and uses very little energy.

With this module, you can control three motor-controlled applications, such as roller blinds, curtains or awnings, for example. By pushing the button, you can also control each motor manually. The run time of the motors can be set with the programming software. Using this module, you can interconnect two zero conductors, this keeps the wiring in the electricity cabinet tidy. The module is equipped with six feedback LEDs and one status LED and uses very little energy.