Verktøy for rørleggerarbeid - side 4

Robust quality tool for removing outer and inner burr from pipes. Stainless steel pipes, other steel pipes, copper, brass, aluminium, steel, plastic pipes Ø 10–54 mm, Ø 1/2–2 1/8.REMS REG 10-54 – the multiple edge up to Ø 54 mm

KNIPEX 87 21 250 Cobra® QuickSet Hightech-vannpumpetang ovetrukket med rutsjhemmende kunststoff grå atramentert 250 mm

Bender, 312m rør

Hand pressure test pump with manometer, p = 60 bar/6 MPa/870 psi, for pressure and tightness testing of pipe systems and containers up to 60 bar/6 MPa/870 psi. Corrosion-resistant, powder-coated steel container for 12 l volume. 1.5 m high-pressure hose with 12" connection. In carton.

KNIPEX 87 51 250 SB Cobra® ES Vannpumpetang ekstra slank ovetrukket med rutsjhemmende kunststoff grå atramentert 250 mm (selvbetjeningskort/blister)

Bender, 406m rør

REMS pressing tongs High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour. Hence far closer tolerances compared to as cast pressing contour.Drive through all REMS radial presses (except REMS Mini-Press ACC) and suitable radial presses of other makes. Read and follow the installation and assembly instructions of the system provider/manufacturer.Traceability according to EN 1775:2007 REMS pressing tongs/pressing rings with pressing contour M, V, SA, B, RN and UP have worked a specific marking into the pressing contour which leaves a lasting impression on the pressed fitting after the pressing process. This enables the user to check again whether the most suitable pressing tongs or the suitable pressing ring have been used to make the pressfit connection even after the pressing process.With this tracability REMS fulfills the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

Ridgid rp-219 jaw 19 kn v28

Ridgid rp-219 jaw 19 kn u16

REMS pressing tongs Mini Very compact design and low weight of the REMS Mini pressing tongs due to special arrangent of the pressing tongs connection (Patent EP 1 952 948).High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour.Drive through REMS Mini-Press ACC drive unit. Read and follow the installation and assembly instructions of the system provider/manufacturer.Traceability according to EN 1775:2007 REMS pressing tongs Mini with pressing contour M, V, SA, B, RN and UP have worked a specific marking into the pressing contour which leaves a lasting impression on the g after the pressing process. This enables the user to check again whether the most suitable pressing tongs have been used to make the pressfit connection even after the pressing process.With this traceability REMS fulfils the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

REMS pressing tongs Mini Very compact design and low weight of the REMS Mini pressing tongs due to special arrangent of the pressing tongs connection (Patent EP 1 952 948).High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour.Drive through REMS Mini-Press ACC drive unit. Read and follow the installation and assembly instructions of the system provider/manufacturer.Traceability according to EN 1775:2007 REMS pressing tongs Mini with pressing contour M, V, SA, B, RN and UP have worked a specific marking into the pressing contour which leaves a lasting impression on the g after the pressing process. This enables the user to check again whether the most suitable pressing tongs have been used to make the pressfit connection even after the pressing process.With this traceability REMS fulfils the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

REMS pressing tongs Mini Very compact design and low weight of the REMS Mini pressing tongs due to special arrangent of the pressing tongs connection (Patent EP 1 952 948).High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour.Drive through REMS Mini-Press ACC drive unit. Read and follow the installation and assembly instructions of the system provider/manufacturer.Traceability according to EN 1775:2007 REMS pressing tongs Mini with pressing contour M, V, SA, B, RN and UP have worked a specific marking into the pressing contour which leaves a lasting impression on the g after the pressing process. This enables the user to check again whether the most suitable pressing tongs have been used to make the pressfit connection even after the pressing process.With this traceability REMS fulfils the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

REMS pressing tongs Mini Very compact design and low weight of the REMS Mini pressing tongs due to special arrangent of the pressing tongs connection (Patent EP 1 952 948).High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour.Drive through REMS Mini-Press ACC drive unit. Read and follow the installation and assembly instructions of the system provider/manufacturer.Traceability according to EN 1775:2007 REMS pressing tongs Mini with pressing contour M, V, SA, B, RN and UP have worked a specific marking into the pressing contour which leaves a lasting impression on the g after the pressing process. This enables the user to check again whether the most suitable pressing tongs have been used to make the pressfit connection even after the pressing process.With this traceability REMS fulfils the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

REMS pressing tongs MiniVery compact design and low weight of the REMS Mini pressing tongs due to special arrangent of the pressing tongs connection (Patent EP 1 952 948).High compression pressing tongs/pressing rings in forged and specially hardened steel. Pressing contours of REMS pressing tongs/pressing rings are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour.Drive through REMS Mini-Press ACC drive unit. Read and follow the installation and assembly instructions of the system provider/manufacturer.

Ridgid tube bender 315m

REMS pressing tongs High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour. Hence far closer tolerances compared to as cast pressing contour.Drive through all REMS radial presses (except REMS Mini-Press ACC) and suitable radial presses of other makes. Read and follow the installation and assembly instructions of the system provider/manufacturer.Traceability according to EN 1775:2007 REMS pressing tongs/pressing rings with pressing contour M, V, SA, B, RN and UP have worked a specific marking into the pressing contour which leaves a lasting impression on the pressed fitting after the pressing process. This enables the user to check again whether the most suitable pressing tongs or the suitable pressing ring have been used to make the pressfit connection even after the pressing process.With this tracability REMS fulfills the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

REMS cutter wheel Cu-INOX for stainless steel pipes of pressfitting systems, copper, carbon steel

KNIPEX 00 11 02 Koplingsskapnøkkel for vanlige skap og sperresystemer 44 mm

Adapter tongs Mini Z8for driving REMS pressing rings S & 45° (PR-2B)

Robust quality tools for cutting tubes. Particularly suited for cutting stainless steel tubes.Copper tubes, thin-walled stainless steel tubes, thin-walled steel, aluminium, brass tubes Ø 6 – 35 mm Ø 18 – 138Cutting wheel:4327920515REMS RAS Cu-INOX – the compact version with telescopic spindle.

Li­Ion PLUS technology. Highly resistant Li-­Ion 12V battery with 2.5 Ah capacity for long service life. Powerful and light. Total discharge and overload protection with single cell monitoring. Temperature monitoring during the charging process. Operating temperature range –10 to +60 °C. No memory effect for maximum battery power.

REMS Tiger ANC VE set. Electric pipe bayonet saw with vario electronics (VE) for easy, fast, perpendicular sawing with pipe holder and for freehand sawing up to 6", 250 mm. Machine with spade handle, maintenance-free, water and dust protected oscillation drive with versatile needle bearing drive (ANC) , aggressive orbital stroke, 230 V, 1050 W, safety rocker switch. Universal saw blade holder for 2". 2 REMS special saw blades 2". In a stable steel case.

REMS pressing tongs High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour. Hence far closer tolerances compared to as cast pressing contour.Drive through all REMS radial presses (except REMS Mini-Press ACC) and suitable radial presses of other makes. Read and follow the installation and assembly instructions of the system provider/manufacturer.

REMS Pull-Push – fast clearance of blockages.Proven, reliable suction and pressure cleaning device for fast clearance of blockages.High pressing force by front, adjustable handle.Optimum adaptation to the cleaning task by 2 sleeves: Short sleeve for wash basins and baths, long sleeve for toilets.

Power-transmitting pipe holder. For assembly and demolition. Unique pipe holder that 5 times the power transfer – allows easy, fast, perpendicular sawing on site, without the use of a vise. Ideal handling, easy and quick operation, just one handle for clamping and sawing. No freely swinging chain and cumbersome operation, as when using a chain vise. No clamping option, as the swing angle is limited. 400% more sawing power available for a power-saving, super-fast sawing during assembly and demolition, e.g. a 4" steel pipe in just 8 seconds. With the pipe holder installed, for optimal sawing, it is recommended to use a straight hand grip.