Verktøy for rørleggerarbeid - side 8

REMS pressing tongs Mini Very compact design and low weight of the REMS Mini pressing tongs due to special arrangent of the pressing tongs connection (Patent EP 1 952 948).High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour.Drive through REMS Mini-Press ACC drive unit. Read and follow the installation and assembly instructions of the system provider/manufacturer.Traceability according to EN 1775:2007 REMS pressing tongs Mini with pressing contour M, V, SA, B, RN and UP have worked a specific marking into the pressing contour which leaves a lasting impression on the g after the pressing process. This enables the user to check again whether the most suitable pressing tongs have been used to make the pressfit connection even after the pressing process.With this traceability REMS fulfils the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

REMS pressing tongs High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour. Hence far closer tolerances compared to as cast pressing contour.Drive through all REMS radial presses (except REMS Mini-Press ACC) and suitable radial presses of other makes. Read and follow the installation and assembly instructions of the system provider/manufacturer.Traceability according to EN 1775:2007 REMS pressing tongs/pressing rings with pressing contour M, V, SA, B, RN and UP have worked a specific marking into the pressing contour which leaves a lasting impression on the pressed fitting after the pressing process. This enables the user to check again whether the most suitable pressing tongs or the suitable pressing ring have been used to make the pressfit connection even after the pressing process.With this tracability REMS fulfills the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

412m ridgid bender 12 mm

REMS Swing set. One-handed pipe bender Ø 10–32 mm, Ø 3/8"-7/8", up to 90°. Soft copper tubes Ø 10–22 mm, Ø 3/8–7/8", s=1mm, soft plastic coated copper tubes Ø 10–18 mm, Ø 3/8"–5/8", s = 1mm, plastic coated C-steel pipe for press fitting system Ø 12–18 mm, mild precision steel pipe Ø 10–18 mm, s=1mm, plastic pipe with metallic insert Ø 14–32 mm. Up to Ø 26 mm with bends, bend segments, universal stop with sliding pieces, in stable steel case/ case. Up to Ø 32 mm with bends, bend segments, 2 stops with sliding pieces, in stable case.

Rørsaks 118 2-i-1

Water pump pliers 250mm, Quick adjust. High alloy steel. Hardness: 50-57 HRc.

KNIPEX 81 03 250 Sifon- og konnektortang ovetrukket med rutsjhemmende kunststoff forkrommet 250 mm

REMS pressing ringsHigh compression pressing rings in forged and specially hardened steel. Pressing contours of REMS pressing rings are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing segments manufactured on CNC production centres ensure high-precision machining of pressing contour. Hence far closer tolerances compared to as cast pressing contour.Traceability according to EN 1775:2007 REMS pressing tongs/pressing rings with pressing contour M have worked a specific marking into the pressing contour which leaves a lasting impression on the pressed fitting after the pressing process. This enables the user to check again whether the most suitable pressing tongs or the suitable pressing ring have been used to make the pressfit connection even after the pressing process.With this tracability REMS fulfills the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.