Viega Trykkrør & Beslag - side 6

Megapress-adapter med SC-Contur for drikkevannsinstallasjon - stålrør i samsvar med DIN EN 10220/10255 med galvanisering i samsvar med DIN EN 10240 - bronse eller silisiumbronse - trykkontakterKomponenterEPDM tetningselementer, skjæring ring, separatorringDN: 40, D: 112, d: 42

Viega 2215.1

Sanpress Inox Reducer with SC-Contur- steel non-corroding- plug-in end, press connectionComponentsEPDM sealing element, VdS certificationd1: 42, d2: 28

Sanpress Inox Connection screw fitting with SC-Contur- steel non-corroding- press connection, G-thread- flat sealingComponentsEPDM sealing element, EPDM flat seal, union nut screw fitting d: 15, G: 12

Profipress g t-piece 28 mm

Press connector system with press connectors and pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DIN EN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-die

Sanpress Inox Crossover with SC-Contur- steel non-corroding- plug-in end, press connectionComponentsEPDM sealing elementd: 15

Sanpress Inox Adapter elbow 90° with SC-Contur- steel non-corroding- press connection, Rp-thread, polygonComponentsEPDM sealing elementd: 15, Rp: 12

Sanpress Inox Plug-in piece- steel non-corroding- plug-in end, Rp-threadComponentsPolygon d: 28, Rp: 34

Sanpress Plug-in piece- gunmetal or silicium bronze- plug-in end, R-threadComponentsPolygon.

Sanpress T-piece with SC-Contur- gunmetal or silicium bronze- press connectorsComponentsEPDM sealing elementsd1: 35, d2: 15, d3: 35

Viega Sanpress overbøyning 22 Rustfritt stål / polert

Viega 1111

Viega 2226.1XL

For installasjon av den interne sirkulasjonsrøret.

Smartloop tilkoblingssett - for varmtvanns stigerør med intern sirkulasjonsrør, varmtvanns stigerør fra d28, sirkulasjonsrør d15 - egnet for Smartloop Pipe PB 2007.3 - messing eller silisiumbronsekomponenter Plug, tilkoblingsstikkontakt d1: 35, d2: 12

Press connector systems with press connectors and pipes made of non-alloy steel 1.0308 (E235), in acc. with EN 10305-3, externally galvanised with a zinc layer thickness of 8–15 m (blue chromatised).Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingRed symbol (to prevent confusion with Sanpress Inox (stainless steel) articles) »Not for drinking water installations«Sealing elementsEPDM, black (ethylene-propylene-dien-monomer rubber),not resistant against hydrocarbon solvent, chlorinated hydrocarbon solvents, turpentine, petrol, FKM, dull blackDimensionsD38

Viega 1115.1

Viega 1112

Viega 1112

Viega 1112.1

Viega 1115.1

Press connector system with press connectors made of gunmetal, pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DINEN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene

Viega 2214

Press connector system with press connectors made of gunmetal, pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DINEN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene