PEX-systemer - side 8

Backplate elbow is used in e.g. utility room.

Transition from 22 mm to pipe thread.

Polyetylenisolering for Pettinaroli vannfordelingsrør CC50. Passer til 4 sirkler og kan enkelt kuttes etter behov. Merk: Kan kun brukes for CC50 og ikke CC35.

Uponor 1009004 VVS-kobling Kompresjonsbøyning

HENCO VISION endestykke for samlebokser til vann-, varme- og elektriske installasjoner. Maks 16 bar

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpresse

Komplett tilpasningssett for flerlagsrør. Messing

HENCO trykktestplugg 20 mm for vann-, varme- og elektriske installasjoner Maks. 16 bar

Manifold for vann med 2 uttak. Inkludert 15 mm tilkobling for polyetylenrør med TEA-overflate.

Fitting in gunmetal for Roth manifold

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Support bushes for Pex and insert fittings.

For assembly of pipes or fittings.

Uponor 1047999 VVS-kobling

Tool for fix of floorheating pipe

Press connection 18 mm x 12

Nipple in gunmetal Roth 3/4" EURO x 3/4", used with female plastic pipe fitting

Messingmanifold med 4 uttak for vann- og varmesystemer.

Manifold for vann TEA 3 uttak 15/10 mm tilkoblinger

Manifold for vann TEA 3 uttak 16/12 mm tilkoblinger

For dry wall, push

Used for QuickBox in plate walls.Remember to order Ø4 x 60 mm screws to fasten the junction boxes, use 2-4 screws per. junction box.

Ekstra bred metallmonteringsbrakett for Uponor avslutningsbokser med skruehull (D4 mm) - c / c 150 mm. - Høyde 70 mm, bredde 360 ​​mm, tykkelse 1,25 mm. - For installasjon i betong, lettveggkonstruksjon og platevegg. Kan monteres i en vegg fra fronten og bakenden.

Adapter for bruk med PPM-manifoldsystemet. Maks trykk: 10 bar. Maks temperatur: 70°C. Montering av adapter og manifold utføres uten bruk av verktøy ved hjelp av en bajonett-kobling.

Used in dry wall to Roth QuickBox, when the installation is extraordinarily deep.