PEX-systemer - side 7

Quickbox double for stone wall

Uponor koblingsboks dobbel M4 15X1/2

Used for For pipe in 25 mm

Unite cutter for multibox

Made of polypropylene. For floor penetrations for radiators. Fits empty pipes with dimensions of 25/20. C/C 40 mm. Can be modified with a spacer block.

Uponor 1009006 VVS-kobling Kompresjonsbøyning

Produsert av PPSU. Q&E manifold med 3/4 hann-gjenger, kun for bruk med Uponor PE-Xa rør

Uponor 19 mm installasjonssett

PPM modulært manifold system for drikkevann i PPSU (polyfenylsulfon). For bajonettadaptere for flere tilkoblinger. Maks trykk: 10 bar Maks temperatur: 70 °C

Uponor 1038037 VVS-kobling Albu

Uponor 1042342 VVS-kobling Albu

Adaptervinkel PPM Uponor 1x3/4.

PPM modulært distribusjonsrørsystem for drikkevann i PPSU (polyfenylsulfon). Med bajonettsokler, leveres med O-ring for utvendig gjenge. Grener med bajonett-koblingssystem, slik at det kan brukes til flere forskjellige adaptere og overgangsstykker. Koblingssystemet kan bare brukes med Ators PE-Xa-rør og Q&E-adaptere eller MLC-rør og trykkadaptere.

Adapter rett ppm Uponor 1x3/4.

Produsert av PPSU. Q&E-systemet skal kun brukes med Uponor PE-Xa-rør

Uponor 1042331 VVS-kobling Endeinngangsforkorter

Uponor 1008679 VVS-kobling Kranadapter

Produsert av PPSU. Q&E-systemet skal kun brukes med Uponor PE-Xa-rør

Uponor 1047999 VVS-kobling

PPM modulært manifold system for drikkevann i PPSU (polyfenylsulfon). For bajonettadaptere for flere tilkoblinger. Maks trykk: 10 bar Maks temperatur: 70 °C

Used for pexpipe

Used for pipe in 20 mm

Backplate elbow is used in e.g. utility room.

Used for Roth gunmetal manifold

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f