Unidrain Dreneringsprodukter - side 8

For shower cubicles without fixed walls.

The drain unit has four floor flanges.

Including four heght-adjustable feet (40-190 mm).

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

For shower cubicles without fixed walls.

The drain unit has four floor flanges.

Including four heght-adjustable feet (40-190 mm).

For testing of the wetroom solution for leaks before laying tiles. Placed in the drain unit. Fill the shower niche with 20-mm water and allow to stand for 24 hours to test the seal.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Can be freely positioned against the back wall, independent of any side walls. The rear flange has been moved 12 mm backwards, to fit 15 -20mm wall tiles + tile mortar + wetroom membrane.

NB! ClassicLine or HighLine frame must be used.

ShowerLine has a built-in slope, so that the floor in the shower cubicle slopes correctly by 2% down towards the floor drain. For added wetroom safety, the shower cubicle is framed by flanges on three sides.

The shower screen is mounted in the track on the fixed module, to eliminate the risk of working loose over time.

Combine with: Outlet unit, frame, grating/panel and shower screen.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

ShowerLine has a built-in slope, so that the floor in the shower cubicle slopes correctly by 2% down towards the floor drain. For added wetroom safety, the shower cubicle is framed by flanges on three sides.

The shower screen is mounted in the track on the fixed module, to eliminate the risk of working loose over time. Combine with: outlet unit, frame, grating/panel and shower screen.

The grate is placed on a recessed bearing in the frame, which ensures precise positioning.

Can only be used with ClassicLine frame.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile).

The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.

The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

The grating is selected from among six attractive designs.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile).

The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.

The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

The grating is selected from among six attractive designs.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

The grate is placed on a recessed bearing in the frame, which ensures precise positioning.

Can only be used with ClassicLine frame.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

With side drain on the right.

Can be freely positioned against the back wall, independent of any side walls. Only for use with ClassicLine.

Can be freely positioned against the back wall, independent of any side walls. The rear flange has been moved 6 mm backwards, to fit 6 – 20mm wall tiles + tile mortar + wetroom membrane.

NB! Only for HighLine Custom frameless.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.