Unidrain Dreneringsprodukter - side 17

Unidrain Drain unit 1004 1200 mm Rear flange

Unidrain Outlet unit w/horizontal outlet Ø75 mm incl. water trap and fire horizontal side inlets Ø40 mm

The water trap is removable and can be taken apart for cleaning

Note: The outlet unit can be used in 3 different ways:
– If the water trap is positioned at the top and the top two side spigots are used as inlets from an external unit, then a separate water trap must be installed on the added unit.
– If the water trap is pushed down into the outlet unit, the external unit connected to the top side spigots will be covered by the included water trap, so there is no need for an external water trap.
– If the bottom two side inlets are used, you must establish an external water trap, regardless of the position of the Unidrain water trap.

Unidrain ClassicLine grating Classic 1200 mm

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

Unidrain Complete drain system corner vertical Ø75 mm

ClassicLine corner drain kit - vertical Ø 75, Column, H 10 mm. The drain kit is the simple solution that contains all the necessary parts for a unidrain® ClassicLine system. The solution is composed of the best-selling products, which can therefore meet the needs of most bathrooms. The solution is available in lengths of 700, 800, 900 and 1000 mm and as a corner solution, and includes: ClassicLine grate (Column), ClassicLine frame (H 10 mm), wooden slats, drainage fixture (1004 with back flange) and outlet housing (Ø75mm vertical incl. trap).

Unidrain Drain unit 4004 800 mm Vinyl

Unidrain Outlet unit w/horizontal outlet Ø32 mm corner drain

Unidrain Drain unit w/horizontal outlet Ø75 mm incl. water trap corner drain

Unidrain ClassicLine frame for corner drain 8 mm

Unidrain ClassicLine frame for corner drain 10 mm

Unidrain Water trap w/50 mm water seal suitable for outlet unit 1418.0050

Unidrain ClassicLine grating Classic for corner drain

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

Unidrain Strainer for corner drain

Unidrain HighLine panel 800 mm Brushed

Unidrain HighLine Colour frame 800/10 mm Brass

Unidrain ClassicLine frame for free-standing drain unit 300/10 mm Brushed steel

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile).

The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.

The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

The grating is selected from among six attractive designs.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Unidrain ClassicLine grating Square 800 mm

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

Unidrain HighLine Colour frame 800/15 mm Brass

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Unidrain HighLine frame 900/25 mm Brushed

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.