Viega 3130

Viega 3240

Beslag med gjenger i henhold til DINEN 10226, del 1, sertifisert for drikkevann i henhold til DIN 1988 og gassinstallasjoner i henhold til TRGI 2008 (merk notatene på modellen), testet i henhold til DVGW-ark GW 6 og GW 393. Sertifikater Gunmetal gjengede beslag - DVGW-Reg.-Nr. DV-7401AO2957 Gjengede forbindelser R-utvendig gjenge, produsert på stedet - hempen uten ruhet av tråden er mulig.

Viega 3121

Press connector system with press connectors made of copper and gunmetal tested in acc. with DVGW worksheet W 534 with DVGW test seal and pipes made of copper in acc. with EN 1057 in acc. with DVGW worksheet GW 392.Suitable for drinking water installations in acc. with DIN 1988.For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-dien-monomer rubber), up to 110 °C

Viega 2416.1

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Long nipple- gunmetal- R-thread

Long nipple- gunmetal- R-thread

Lang brystvorte i gunmetal med R-gjenge. R: 34, L: 120 mm

Long nipple- gunmetal- R-thread

Long nipple- gunmetal- R-thread

Lang brystvorte- gunmetal- R-gjenge: 12, L: 60

Fittings with threads in acc. with DINEN 10226, Part 1, certified for drinking water in acc. with DIN 1988 and gas installations in acc. with TRGI 2008 (observe notes on the model), tested in acc. with DVGW worksheet GW 6 and GW 393.CertificatesGunmetal threaded fittings – DVGW-Reg.-No. DV-7401AO2957Threaded connectionsR-external thread, produced on site – hempen without roughening of the thread is possible.

Beslag med gjenger i henhold til DINEN 10226, del 1, sertifisert for drikkevann i henhold til DIN 1988 og gassinstallasjoner i henhold til TRGI 2008 (merk notatene på modellen), testet i henhold til DVGW-ark GW 6 og GW 393. Sertifikater av bronse-gjengede beslag - DVGW-Reg.-Nr. DV-7401AO2957 Gjengede forbindelser R-ytre gjenge, produsert på stedet - hempen uten ruhet av tråden er mulig.

Kobling- gunmetal- Rp-gjengeRp: 112

Viega Klaproset White two-part, for toilet connection bends and spigots, with marking for bevel cut.

Viega reducer 3242 3/4, Rp: 1 1/4 Silicium bronze.

Nipple pipe- gunmetal- G-thread.

Kloset Connection pipe 150 mm. White.

T-stykke- messing- Rp-gjengeRp1: 212, Rp2: 212, Rp3: 212

Nipple pipe- gunmetal- G-thread.

Ø 40mm. For 1 1/2" bottom valve. Plastic.

Viega 1118

Prestabo T-piece with SC-Contur- galvanised non-alloyed steel- press connectorsComponentsEPDM sealing elementsd1: 22, d2: 18, d3: 22