Prestabo Crossover galvanised non-alloyed steel plug-in ends Galvanised non-alloyed steel plug-in ends

Viega 2312.1

Fittings with threads in acc. with DINEN 10226, Part 1, certified for drinking water in acc. with DIN 1988 and gas installations in acc. with TRGI 2008 (observe notes on the model), tested in acc. with DVGW worksheet GW 6 and GW 393.CertificatesGunmetal threaded fittings – DVGW-Reg.-No. DV-7401AO2957Threaded connectionsR-external thread, produced on site – hempen without roughening of the thread is possible.

Kryss-over kobber-loddet tilkobling: 22 (kvalitetssegl for d12-54)

Megapress-adapter med SC-Contur for stålrør i samsvar med DIN EN 10220/10255 - ulegert stål, sink-nikkelbelegg - trykkforbindelse, R-gjengekomponenter EPDM tetningselement, skjæring ring, separatorring, polygon DN: 10, D: 38 , R: 38

Viega 1116.1XL

Prestabo Adapter with SC-Contur- galvanised non-alloyed steel- press connection, R-threadComponentsEPDM sealing element, polygon, VdS certificationd: 28, R: 12

Press connector system with press connectors and pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DIN EN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-die

Vanntett tilkoblingskontakt for fleksibel Polybutene. - ikke egnet for PE-X / AI / PE-X, PE-Xc- messing- Rp-gjenge- lydisolering Med vinkel i messing, trykktestdyse Modell 5330

Viega 2214.2

Skru tilkobling i gunmetal med Rp-gjenge. Rp: 34

Long nipple- gunmetal- R-thread

Long nipple- gunmetal- R-thread

Long nipple- gunmetal- R-threadR: 1, L: 40

Long nipple- gunmetal- R-thread

Beslag med gjenger i henhold til DINEN 10226, del 1, sertifisert for drikkevann i henhold til DIN 1988 og gassinstallasjoner i henhold til TRGI 2008 (merk notatene på modellen), testet i henhold til DVGW-ark GW 6 og GW 393. Sertifikater Gunmetal gjengede beslag - DVGW-Reg.-Nr. DV-7401AO2957 Gjengede forbindelser R-utvendig gjenge, produsert på stedet - hempen uten ruhet av tråden er mulig.

Fittings with threads in acc. with DINEN 10226, Part 1, certified for drinking water in acc. with DIN 1988 and gas installations in acc. with TRGI 2008 (observe notes on the model), tested in acc. with DVGW worksheet GW 6 and GW 393.CertificatesGunmetal threaded fittings – DVGW-Reg.-No. DV-7401AO2957Threaded connectionsR-external thread, produced on site – hempen without roughening of the thread is possible.

Plug- gunmetal- R-threadComponentsQuadraticR: 38

Plug- gunmetal- R-threadComponentsQuadraticR: 12

Long nipple- gunmetal- R-thread

Long nipple- gunmetal- R-thread

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Fittings with threads in acc. with DINEN 10226, Part 1, certified for drinking water in acc. with DIN 1988 and gas installations in acc. with TRGI 2008 (observe notes on the model), tested in acc. with DVGW worksheet GW 6 and GW 393.CertificatesGunmetal threaded fittings – DVGW-Reg.-No. DV-7401AO2957Threaded connectionsR-external thread, produced on site – hempen without roughening of the thread is possible.

Long nipple- gunmetal- R-thread

Plug- gunmetal- R-threadComponentsQuadraticR: 34