Viega - side 29

Viega 3241

Reducer- chromium-plated gunmetal- R-thread, Rp-threadComponentsPolygonR: 34, Rp: 12

Viega Blok 12 mm x 1/2" with bent back pad. For solder connection, insertion dimension. 150 mm, with short redware angles, with bent holder.

T-stykke - kobber - loddeforbindelse d1: 28, d2: 22, d3: 28 (kvalitetsmerke for d12-54)

Tilkoblingsskrue montering - bronsefarget - R-gjenge, G-gjenge - flat tetning. Komponenter: Polygon, flat tetning AFM 34

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Press connector system with press connectors and pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DIN EN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-die

Viega 2212

Sanpress Inox Adapter elbow 90° with SC-Contur- steel non-corroding- press connection, Rp-thread, polygonComponentsEPDM sealing elementd: 15, Rp: 12

Sanpress Inox Plug-in piece- steel non-corroding- plug-in end, Rp-threadComponentsPolygon d: 28, Rp: 34

Long nipple- gunmetal- R-thread

Redusere kobling - kobber - loddet tilkobling d1: 12, d2: 10

Profipress g t-piece 28 mm

Universal valve with stainless steel valve upper part, with plug, plastic valve lower part, silver-coloured.

Lang brystvorte i gunmetal med R-gjenge. R: 1, L: 110 mm

Viega 1112.1

Viega 2616.1

Profipress T-stykke med SC-Contur-kobberpresskoblingerKomponenterEPDM-tetningselementer, VdS-sertifiseringd1: 35, d2: 35, d3: 35

Raxofix T-piece with SC-Contur- silicium bronze- press connectors.

Rørklips plast enkelt for d: 24

Viega 1115.1

Sanpress Plug-in piece- gunmetal or silicium bronze- plug-in end, R-threadComponentsPolygon.

Sanpress Inox Connection screw fitting with SC-Contur- steel non-corroding- press connection, G-thread- flat sealingComponentsEPDM sealing element, EPDM flat seal, union nut screw fitting, VdS certificationd: 22, G: 34

Press connector system with press connectors and pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DIN EN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-die

Sanpress Inox Reducer with SC-Contur- steel non-corroding- plug-in end, press connectionComponentsEPDM sealing element, VdS certificationd1: 42, d2: 28