Viega - side 11

Press connector system with press connectors made of copper and gunmetal tested in acc. with DVGW worksheet W 534 with DVGW test seal and pipes made of copper in acc. with EN 1057 in acc. with DVGW worksheet GW 392.Suitable for drinking water installations in acc. with DIN 1988.For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-dien-monomer rubber), up to 110 °C

Viega 2218

Easytop circulation valve S/E thermostatic control valve for string or floor systems. Silicon bronze. G thread. Can be blocked off. Cylindrical G-thread according to ISO 228 for flat-sealing fittings, valve body made of silicon bronze according to DIN 50930-6 / DIN EN 1982, stainless steel ball, drain plug.

Long nipple- gunmetal- R-thread

Elbow 90°- gunmetal- R-thread, Rp-thread

Adapter - gunmetal - soldered connection, Rp-thread.

Raxofix Adapter with SC-Contur- for all Viega metallic systems- silicium bronze- press connectorsComponentsEPDM sealing elementd1: 16, d2: 15

Viega 3130

Viega 2616.1

Viega 1115.1

Long nipple- gunmetal- R-thread

Sanpress XL Reducer with SC-Contur- gunmetal- plug-in end, press connectionComponentsEPDM sealing element, cutting ringd1: 88.9, d2: 76.1

Sanpress T-stykke med SC-Contur- gunmetal eller silisiumbronse- presskoblinger. Komponenter: EPDM tetningselementer d1: 35, d2: 35, d3: 35

Raxofix Adapter elbow 90° with SC-Contur- silicium bronze- press connection, R-threadd: 16, R: 34

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Viega 5318

Viega Extension 3525.

Adapter albue 90° - bronsefarget - loddet tilkobling, Rp-gjenge d: 22, Rp: 34

Viega 1111XL

Vanntett tilkoblingskontakt for fleksibel Polybutene. - ikke egnet for PE-X / AI / PE-X, PE-Xc- messing- Rp-gjenge- lydisolering Med vinkel i messing, trykktestdyse Modell 5330

Raxofix Coupling with SC-Contur- silicium bronze- press connectiond1: 25, d2: 16

Viega 2234

Press connector system with press connectors made of gunmetal, pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DINEN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene

Viega Blok 15 mm x 1/2" with bent back pad. For solder connection, insertion dimension. 150 mm, with short redware angles, with bent holder.

Easytop Ball valve with SC-Contur- press connectorsComponentsValve casing gunmetal or silicium bronze according to DIN 50930-6 / DIN EN 1982, maintenance-free selector shaft, actuation lever T-form with medium marking green/red exchangeable, stainless steel ball, EPDM sealing elements.Technical dataoperating pressure max. 1.6 MPa (PN 16)operating temperature max. 110 °Cwith DVGW-test markDN: 50, d: 54