Gulvvarme - side 6

Ferdigmontert lineært manifold med mikrometrisk manøvrering, med termostatisk alternativ eller elektrisk kontroll, for returledninger. Komprimeringsender. Uten tilkoblinger. 3 uttak.

SALUS GVU is a complete floor heating shunt solution for underfloor heating with underfloor heating manifold, shunt and circulation pump built together in one unit.Our circulation pump is a 6m pump with capacity up to 16 zones. The underfloor heating manifold is a high flow manifold with manual balancing of each circuit. Each valve has a built-in manual flow control which is very easy to adjust. Instructions on how to balance the circuit can be found in the distributor box.The SALUS GVM floor heating manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The Inlet thermostat has a temperature setting of 20 to 55 degrees Celsius. Manifold pipe connection is 1 ", and connection to water for the heat supply is 3/4" socket, and threads to the actuator are 30 x 1.5 mm.

SALUS GVU is a complete floor heating shunt solution for underfloor heating with underfloor heating manifold, shunt and circulation pump built together in one unit.Our circulation pump is a 6m pump with capacity up to 16 zones. The underfloor heating manifold is a high flow manifold with manual balancing of each circuit. Each valve has a built-in manual flow control which is very easy to adjust. Instructions on how to balance the circuit can be found in the distributor box.The SALUS GVM floor heating manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The Inlet thermostat has a temperature setting of 20 to 55 degrees Celsius. Manifold pipe connection is 1 ", and connection to water for the heat supply is 3/4" socket, and threads to the actuator are 30 x 1.5 mm.

Amplifier for Salus iT600 heating system ZigBee signal.

SALUS GVM-F underfloor heating manifold is a high flow manifold with manual balancing of each circuit.Each zone valve has on the flow pipe a flow meter that can be used for balancing. Alternatively, the built-in manual flow control integrated into the return valve on the return pipe can be used for balancing. Instructions on how to balance the circuit can be found in the distributor box.SALUS GVM-F underfloor heating distributor has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. Inlet and return pipe connection is 1 ”thread, and the actuator thread is 30 x 1.5 mmContains:Stainless steel manifold set with flow meterEuroconus set for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting brackets for wall mountingWith individual room temperature control. SALUS GVM-F benefits are available with SALUS - wireless control.Properties:Available with SALUS insulation in form-stable EPPComplies with the installation requirements for insulation standard DS 452.Ready for wall mounting.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.• Can be integrated into the SALUS Smart Home solution.Can be operated directly from the room thermostat or from the mobile phone, tablet or computer.Benefits are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension1 ”, for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum test pressure: 10 bar

Used for floorheating systems

Used on Giacomini manifold

SALUS GVM-F underfloor heating manifold is a high flow manifold with manual balancing of each circuit.Each zone valve has on the flow pipe a flow meter that can be used for balancing. Alternatively, the built-in manual flow control integrated into the return valve on the return pipe can be used for balancing. Instructions on how to balance the circuit can be found in the distributor box.SALUS GVM-F underfloor heating distributor has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. Inlet and return pipe connection is 1 ”thread, and the actuator thread is 30 x 1.5 mmContains:Stainless steel manifold set with flow meterEuroconus set for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting brackets for wall mountingWith individual room temperature control. SALUS GVM-F benefits are available with SALUS - wireless control.Properties:Available with SALUS insulation in form-stable EPPComplies with the installation requirements for insulation standard DS 452.Ready for wall mounting.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.• Can be integrated into the SALUS Smart Home solution.Can be operated directly from the room thermostat or from the mobile phone, tablet or computer.Benefits are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension1 ”, for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum test pressure: 10 bar

Used for floorheating systems

Used between floorheating pipe and Roth manifold.

Used on Uponor manifold

Wavin TIGRIS HEATDISTRIBUTI PLATE A,20MM PEX

Fullstendig manifold system, inn- og utløp, inkludert braketter, 20 mm tilkoblinger og endestykker. 12 uttak.

DEVIpipeheat 10 V3, 14m Self limiting with Danish plug

The THB23031 is an auto balancing actuator that is used to provide automatic balancing of your underfloor heating circuits. It has two temperature sensors that are connected to the UFH flow and return pipes (inlet and outlet of the UFH manifold). It will continuosly measure the temperatures and adjust the actuator position to maintain the correct temparatur differential between the manifold flow and return pipes (Delta T). This product has an IP54 rating means that the produkt will be protected against contamination from limited amounts of dust and other particles. Additionally, it will be protected from water sprays from all directions. ITG Dresden have confirmed that the Salus THB actuator is equivalent to the hydraulic balancing. In co-operation with ITG Dresden, The Salus THB actuator has been tested and improved. During independent testing it was confirmed that the installation of the Salus THB system in existing underfloor heating system will achieve the same results as a conventional balancing.

Wiring centre extension for Salus iT600 gulvarmesystem.

Fullstendig manifold system, inn- og utløp, inkludert braketter, 20 mm tilkoblinger og endestykker. 5 uttak.

Termostatisk hode for 7021.

DEVIpipeheat 10 V3, 6m Self limiting with Danish plug

Pump with 6 m lifting height and dimensions 180 mm.The pump is A + rated, that is, power consumption is minimal.

SALUS GVM-F underfloor heating manifold is a high flow manifold with manual balancing of each circuit.Each zone valve has on the flow pipe a flow meter that can be used for balancing. Alternatively, the built-in manual flow control integrated into the return valve on the return pipe can be used for balancing. Instructions on how to balance the circuit can be found in the distributor box.SALUS GVM-F underfloor heating distributor has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. Inlet and return pipe connection is 1 ”thread, and the actuator thread is 30 x 1.5 mmContains:Stainless steel manifold set with flow meterEuroconus set for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting brackets for wall mountingWith individual room temperature control. SALUS GVM-F benefits are available with SALUS - wireless control.Properties:Available with SALUS insulation in form-stable EPPComplies with the installation requirements for insulation standard DS 452.Ready for wall mounting.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.• Can be integrated into the SALUS Smart Home solution.Can be operated directly from the room thermostat or from the mobile phone, tablet or computer.Benefits are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension1 ”, for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum test pressure: 10 bar

SALUS GVM underfloor heating manifold is a high flow distributor with manual balancing of each circuit.Each valve has a built-in manual flow control which is very easy to adjust. Instructions for balancing the circuit can be found in the distributor box.The SALUS GVM manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The inlet- and return- connection is 1 ”thread, and the thread for the actuators are 30 x 1.5 mmContains:Stainless steel distributor set with valveEurokonus for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting bracket for wall mountingWith individual room temperature control.Salus GVM underfloor heating distributors can be supplied with SALUS wireless control.Properties of Salus Underfloor Heating Manifold:Available with Salus insulation in form-stable EPP.Meets the installation requirements for insulation standard DS 452.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.Ready for wall mounting.Can be integrated into the Salus Smart Home solution.Can be operated directly from the room thermostat and from the mobile phone, tablet or computer.The distribution pipes are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension 1 ”for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum proofing pressure: 10 bar

for one jig.

Used on Roth manifold

Nødvendig modul for de som ønsker å ha et trådløst systemFunksjoner Radiomodul• Nødvendig modul• Sender og mottar trådløse signaler mellom romtermostater og Master Controller