Gulvvarme - side 10

Moduler for 1,3,4,6 sløyfer som kan kombineres til maks. 12 sløyfer for tilkobling med grunnleggende sett, tilkobling høyre eller venstre med flat tetning eller tilkobling nedenfra med valgfritt albuesett. Leveres med låseventil for balansering (med justeringsring) og avstengning, justeringsring for balansering uten verktøy, klargjorte steder for romnavnelapper. Retur med ventiler og kapsler, klargjort for aktuatorer nr.1000138 (24V hann) nr. 1005605 (230V hann), sløyfe-tilkobling Q&E 20,Q&E17 komplett med Q&E-ringer1025659 ,1042836 løkkeavstand50 mm headeravstand225 mm maks trykk:6 bar maks temperatur:60°C materiale:fiberarmert polyamid

Floorheating with high energy efficiency

Roth Clima Comfort FLOW is a fibre-reinforced, cement-based, selflevelling compound specifically designed for laying together with Roth Clima Comfort system panels or Roth Compact System.

Termostatventil "kun for shunt 7021". 3/4" vinkelventil.

Basic package Uponor pro

Danfoss End-seksjon - Endestykker, braketter og andre tilbehør for FHF-manifoldserien. Endestykke med manuell luftventil

Isolasjon for Danfoss manifold FHF og FH-ME

Devi fitting

MINISHUNT med en utløp. Inkludert UPM2 15/20 pumpe og 20 mm PEX-tilkoblinger.

Uponor 1065284 VVS-kobling Kompresjonsendestykke

Uponor 1013426 VVS-kobling Kompresjonsendestykke

Nødvendig modul for de som ønsker å ha et trådløst systemFunksjoner Radiomodul• Nødvendig modul• Sender og mottar trådløse signaler mellom romtermostater og Master Controller

SALUS GVU is a complete floor heating shunt solution for underfloor heating with underfloor heating manifold, shunt and circulation pump built together in one unit.Our circulation pump is a 6m pump with capacity up to 16 zones. The underfloor heating manifold is a high flow manifold with manual balancing of each circuit. Each valve has a built-in manual flow control which is very easy to adjust. Instructions on how to balance the circuit can be found in the distributor box.The SALUS GVM floor heating manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The Inlet thermostat has a temperature setting of 20 to 55 degrees Celsius. Manifold pipe connection is 1 ", and connection to water for the heat supply is 3/4" socket, and threads to the actuator are 30 x 1.5 mm.

Pettinaroli gateway alpha 230v

Danfos Link HC master regulator 10. Wireless temperature control – all around the house. Danfoss Link is intelligent and wireless communication technology on the inside and stylish on the outside with its timeless design. For total control of your ind

Danfoss kompresjonskoblinger. Koplinger, RA 15/6T, RA 15/6TB, RLV-K, RLV-KD, RLV-KS, RA-C 15, Manifold CFD.

Danfoss SSM underfloor heating manifold in stainless steel with output for 2 heating circuits. SSM floor heating manifolds are equipped with integrated vents and filling/draining function on both flow and return manifold. Manifold SSM is used for heat control in underfloor heating systems. Each hose in the underfloor heating system is connected to the manifold, which makes it possible to regulate the heat supply to all rooms in the building independently. The manifold consists of a flow manifold and a return manifold. The flow manifold allows you to close each circuit independently. The manifold is without a built-in flowmeter. The return manifold is equipped with Danfoss' preset valves, which ensures optimal water balance in the system. The manifold valves can be controlled electronically using thermo actuators. The manifold is available in modules from 2-12 heating circuits. In addition, there are fittings that allow the manifolds to be combined in series - up to a maximum of 16 heating circuits. Ball valves are offered as an option for shutdown between the manifold and the rest of the system.

Insulated bace module with stainless floor heating manifold incl. Drain, air screw and 20mm connector. Rødgod distributors for domestic water incl. 15mm connector. The base modules have universal adaptation, so they fit the market's well-known brands with easy adjustment. Unique for SALUS base module. Connection at the top from right to left KV Cold water-VV Hot water-VF Heating forward-VR Heating return.Insulated distributors and pipes according to DS452The underfloor heating control is mounted directly on the bottom module DIN.

SALUS GVU is a complete floor heating shunt solution for underfloor heating with underfloor heating manifold, shunt and circulation pump built together in one unit.Our circulation pump is a 6m pump with capacity up to 16 zones. The underfloor heating manifold is a high flow manifold with manual balancing of each circuit. Each valve has a built-in manual flow control which is very easy to adjust. Instructions on how to balance the circuit can be found in the distributor box.The SALUS GVM floor heating manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The Inlet thermostat has a temperature setting of 20 to 55 degrees Celsius. Manifold pipe connection is 1 ", and connection to water for the heat supply is 3/4" socket, and threads to the actuator are 30 x 1.5 mm.

Moduler for 1,3,4,6 sløyfer som kan kombineres til maks. 12 sløyfer for tilkobling med grunnleggende sett, tilkobling høyre eller venstre med flat tetning eller tilkobling nedenfra med valgfritt albuesett. Leveres med låseventil for balansering (med justeringsring) og avstengning, justeringsring for balansering uten verktøy, klargjorte steder for romnavnelapper. Retur med ventiler og kapsler, klargjort for aktuatorer nr.1000138 (24V hann) nr. 1005605 (230V hann), sløyfe-tilkobling Q&E 20,Q&E17 komplett med Q&E-ringer1025659 ,1042836 løkkeavstand50 mm headeravstand225 mm maks trykk:6 bar maks temperatur:60°C materiale:fiberarmert polyamid

Moduler for 1,3,4,6 sløyfer som kan kombineres til maks. 12 sløyfer for tilkobling med grunnleggende sett, tilkobling høyre eller venstre med flat tetning eller tilkobling nedenfra med valgfritt albuesett. Leveres med låseventil for balansering (med justeringsring) og avstengning, justeringsring for balansering uten verktøy, klargjorte steder for romnavnelapper. Retur med ventiler og kapsler, klargjort for aktuatorer nr.1000138 (24V hann) nr. 1005605 (230V hann), sløyfe-tilkobling Q&E 20,Q&E17 komplett med Q&E-ringer1025659 ,1042836 løkkeavstand50 mm headeravstand225 mm maks trykk:6 bar maks temperatur:60°C materiale:fiberarmert polyamid

Danfoss SSM underfloor heating manifold in stainless steel with output for 11 heating circuits. SSM floor heating manifolds are equipped with integrated vents and filling/draining function on both flow and return manifold. Manifold SSM is used for heat control in underfloor heating systems. Each hose in the underfloor heating system is connected to the manifold, which makes it possible to regulate the heat supply to all rooms in the building independently. The manifold consists of a flow manifold and a return manifold. The flow manifold allows you to close each circuit independently. The manifold is without a built-in flowmeter. The return manifold is equipped with Danfoss' preset valves, which ensures optimal water balance in the system. The manifold valves can be controlled electronically using thermo actuators. The manifold is available in modules from 2-12 heating circuits. In addition, there are fittings that allow the manifolds to be combined in series - up to a maximum of 16 heating circuits. Ball valves are offered as an option for shutdown between the manifold and the rest of the system.

SALUS GVM underfloor heating manifold is a high flow distributor with manual balancing of each circuit.Each valve has a built-in manual flow control which is very easy to adjust. Instructions for balancing the circuit can be found in the distributor box.The SALUS GVM manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The inlet- and return- connection is 1 ”thread, and the thread for the actuators are 30 x 1.5 mmContains:Stainless steel distributor set with valveEurokonus for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting bracket for wall mountingWith individual room temperature control.Salus GVM underfloor heating distributors can be supplied with SALUS wireless control.Properties of Salus Underfloor Heating Manifold:Available with Salus insulation in form-stable EPP.Meets the installation requirements for insulation standard DS 452.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.Ready for wall mounting.Can be integrated into the Salus Smart Home solution.Can be operated directly from the room thermostat and from the mobile phone, tablet or computer.The distribution pipes are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension 1 ”for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum proofing pressure: 10 bar

SALUS GVU is a complete floor heating shunt solution for underfloor heating with underfloor heating manifold, shunt and circulation pump built together in one unit.Our circulation pump is a 6m pump with capacity up to 16 zones. The underfloor heating manifold is a high flow manifold with manual balancing of each circuit. Each valve has a built-in manual flow control which is very easy to adjust. Instructions on how to balance the circuit can be found in the distributor box.The SALUS GVM floor heating manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The Inlet thermostat has a temperature setting of 20 to 55 degrees Celsius. Manifold pipe connection is 1 ", and connection to water for the heat supply is 3/4" socket, and threads to the actuator are 30 x 1.5 mm.

Uponor Smatrix Wave slave modul M-160