Tilta Foto- & Videotilbehør

Tilta Right Side Wooden Handle 2.0 Håndtak

For Hydra Alien Mini, compatible with DJI Osmo Pocket 3

Tilta Nucleus-M Wireless Lens Control System Partial Kit III
The Tilta Nucleus-M Wireless Lens Control System Partial Kit III contains the essential elements for pulling focus wirelessly while handholding. The kit includes the Nucleus-M left handgrip controller, one Nucleus-M motor, one removable lens belt, two motor power cables, and a battery charger unit (batteries not included). The handgrip controller provides wireless fingertip lens control while functioning as handgrip support for your camera rig, and the system enables pulling either focus, iris, or zoom on your lens. If you are using a lens that does not have standard cine-style gears, then use the included lens belt to add gears to your lens.

This partial kit is a single axis system, but the Nucleus-M left handgrip controller will allow you to control additional motors (not included) so you can control more than one lens ring. The included motor power cables allow you to power a motor from either a D-Tap power source or a second motor via the 7-pin to 7-pin connector. The included power cables allow you to easily add a second motor (not included) to the system. The included rosettes aid in mounting the handgrip controller to your camera or rig with ARRI-style rosettes. The system can wirelessly pull focus from up to 1000' away, and with separately available batteries you can power the hand unit for approximately 10 hours on a single charge.

This support bracket helps to fully stabilize and secure your camera when mounted on the Gravity G1, G2, or G2X by attaching from the tilt arm of the gimbal to the hot shoe mount of your camera.

Tilta MB-T15-TF kameramonteringstilbehør Monteringsklemme

Tilta TA-QRTH5 kameramonteringstilbehør Kamerahåndtak

Sony’s long awaited, flagship mirrorless video/photo camera, the A7sIII, has finally arrived. Made specifically for video content creators that demand excellent low light performance, numerous recording options, and long recording times, the new A7sIII builds upon the legacy of the A7sII to deliver a camera that hits all the right spots for a camera of this level.

Inspired by the usefulness and ingenuity of this camera’s design, Tilta set off to incorporate new design touches that help elevate the camera even further. As part of the Tiltaing series of products, Tilta has put together a versatile, yet lightweight camera cage that is just the beginning for building a camera rig for professional video. The new camera cage is designed to augment and protect the a7sIII, as well as add expansion options like our new rotating top handle, rotating side handles, ARRI standard rosette mounts, and much more.

This camera cage provides complete protective armor for the Fujifilm X-T3 and X-T4 cameras.

It provides several 1/4”-20 mounting points as well as two cold shoe mounting points.

The base of the cage also provides several mounting holes when attaching your camera to gimbals to more easily fine tune the balance of your setup.

A variety of different baseplates can be attached to the bottom of the cage, allowing for various rod mounting and optional power supply configurations.

The quick release top handle and various optional side handles can be attached to the cage to provide for different ways to comfortably operate your camera setup.

This kit of the Fujifilm X-T3/X-T4 cage includes: the base Fujifilm X-T3/X-T4 cage, quick release top handle, Arca and Manfrotto quick release baseplates, as well as a clamp to attach an HDMI cable comfortably to the cage (one specifically for the X-T3 and one for the X-T4).

Compatible with Type II Baseplates and Type I Side Handles.

This camera cage provides protective armor for the Sony a7S III camera. It provides several 1/4"-20 mounting points as well as one cold shoe mounting point. The base of the cage also provides several mounting holes when attaching your camera to gimbals to more easily fine tune the balance of your setup.
A variety of different baseplates can be attached to the bottom of the cage, allowing for various rod mounting and optional power supply configurations.
A quick release top handle can be attached to the cage to provide for a comfortable camera operating setup.

Made specifically for video content creators that demand excellent low light performance, numerous recording options, and long recording times, the new A7sIII builds upon the legacy of the A7sII to deliver a camera that hits all the right spots for a camera of this level.

Inspired by the usefulness and ingenuity of this camera's design, Tilta set off to incorporate new design touches that help elevate the camera even further. As part of the Tiltaing series of products, Tilta has put together a versatile, yet lightweight camera cage that is just the beginning for building a camera rig for professional video. The new camera cage is designed to augment and protect the a7sIII, as well as add expansion options like our new rotating top handle, rotating side handles, ARRI standard rosette mounts, and much more.

This camera cage provides complete protective armor for the Panasonic GH4, GH5, and GH5S cameras. It provides several 1/4”-20 and 3/8”-16 mounting points as well as two cold shoe mounting points. The base of the cage also provides several mounting holes when attaching your camera to gimbals to more easily fine tune the balance of your setup.

A variety of different baseplates can be attached to the bottom of the cage, allowing for various rod mounting and optional power supply configurations.

The quick release top handle and various optional side handles can be attached to the cage to provide for different ways to comfortably operate your camera setup.

This kit of the Panasonic GH Series cage includes: the base Panasonic GH Series cage, quick release top handle, Tilta Hand Strap, Arca and Manfrotto quick release baseplates, a 15mm LWS baseplate for mounting accessories (as well as a single 15mm rod mounting clamp), an HDMI male to HDMI female cable, as well as a clamp to attach the HDMI cable comfortably to the cage and a clamp to attach both the HDMI and Nucleus Nano R/S cable comfortably to the cage.

This camera cage provides complete protective armor for the Fujifilm X-T3 and X-T4 cameras.

It provides several 1/4”-20 mounting points as well as two cold shoe mounting points.

The base of the cage also provides several mounting holes when attaching your camera to gimbals to more easily fine tune the balance of your setup.

A variety of different baseplates can be attached to the bottom of the cage, allowing for various rod mounting and optional power supply configurations.

The quick release top handle and various optional side handles can be attached to the cage to provide for different ways to comfortably operate your camera setup.

This kit of the Fujifilm X-T3/X-T4 cage includes: the base Fujifilm X-T3/X-T4 cage, quick release top handle, Arca and Manfrotto quick release baseplates, as well as a clamp to attach an HDMI cable comfortably to the cage (one specifically for the X-T3 and one for the X-T4).

Compatible with Type II Baseplates and Type I Side Handles.

These cables for the Nucleus-M give you run/stop capabilities in camera systems that support it. Simply plug the 7-pin end of the cable into one of the motors and the other end into the R/S port of the camera.

Note that this cable was specifically designed for the Nucleus-M so the R/S function only works with the Nucleus-M’s own hand unit and hand grips.

Weight: 0.09lbs
Length: 68.6cm
Color: Black
Materials: Copper, rubber, aluminum-alloy

When configured with the Gravity G Series Dual Pistol Grip Battery Handles, an operator can extend the G1/G2/G2X gimbal body’s operating life with eight fully charged 18650 batteries (4 in each handle). This will give up to 20 hours of power to your gimbal. If used in conjunction with the G1/G2/G2X Battery Pistol Grip Handle, up to 30 hours of runtime can be achieved.

Tilta MB-T15-58 camera filter tilbehør Filterholder-adapterring

Tilta MB-T16-SCF camera filter tilbehør

Tilta RS-TA-RD1 videostabilisatortilbehør Kontrollkabel Svart Kopper, Rustfritt stål 1 stykker RED Camera

This camera cage provides complete protective armor for the Fujifilm X-T3 and X-T4 cameras.

It provides several 1/4”-20 mounting points as well as two cold shoe mounting points.

The base of the cage also provides several mounting holes when attaching your camera to gimbals to more easily fine tune the balance of your setup.

A variety of different baseplates can be attached to the bottom of the cage, allowing for various rod mounting and optional power supply configurations.

The quick release top handle and various optional side handles can be attached to the cage to provide for different ways to comfortably operate your camera setup.

This kit of the Fujifilm X-T3/X-T4 cage includes: the base Fujifilm X-T3/X-T4 cage, quick release top handle, Arca and Manfrotto quick release baseplates, a clamp to attach an HDMI cable comfortably to the cage (one specifically for the X-T3 and one for the X-T4), and finally the Tiltaing Side Power Handle with Run/Stop Type I (F570 Battery) along with the compatible Fujifilm X series R/S cable.

Compatible with Type II Baseplates and Type I Side Handles.

Tilta MB-T15-62 camera filter tilbehør Filterholder-adapterring

Tilta MB-T15-C85 camera filter tilbehør Step down-ring (filter)

- Retains access to the camera shoe mount, ports, battery, and display
- Multiple 1/4"-20 accessory threads
- 1/4"-20 camera mounting screw
- Removable Manfrotto-style plate fits Manfrotto-compatible baseplates
- 1/4"-20 mounting threads on the bottom for tripod mounting
- One integrated shoe mount
- Integrated single rod port for optional Tilta single-rod mount
- Aluminum and steel construction

Tilta TA-AMB-B kameramonteringstilbehør

This camera cage provides protective armor for the RED Komodo camera. It provides several 1/4”-20 and 3/8”-16 mounting points for mounting accessories. It also includes two rosettes on each side as well as a cold shoe mount on top. The base of the cage also provides several mounting holes when attaching your camera to gimbals to more easily fine tune the balance of your setup.

A variety of different baseplates can be attached to the bottom of the cage, allowing for various rod mounting and optional power supply configurations.

The quick release top handle, adjustable quick release top handle, and various optional side handles can be attached to the cage to provide for different ways to comfortably operate your camera setup.

This kit of the RED Komodo camera cage will help to fully build out your setup. It includes: the base RED Komodo cage, right side wooden handle, quick release top handle, Arca and Manfrotto quick release baseplates, 15mm LWS baseplate, an Adjustable Cold Shoe Accessory Mounting Bracket, and finally a Dual Canon BP to V Mount Adapter Battery Plate to allow for a longer battery life for your camera.

Tilta TT-C07 kameramonteringstilbehør Svalehaleplate

Tilta TA-SFH1-97-G kameramonteringstilbehør Håndtak

Khronos Adjustable Handle Space Grey