Dreneringsprodukter - side 34

Ramme Unidrain 8 mm.

Horizontal outlet Ø 75 mm, including water trap.

Two horizontal side inlets, 40 mm, which can be opened as needed. 2 rubber adapters are included so that side inlets can be reduced to 32 mm. Easy access to the removable water trap for cleaning. Meets EN1253 standard and is VA approved.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile).

The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.

The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

The grating is selected from among six attractive designs.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile).

The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.

The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

The grating is selected from among six attractive designs.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

The grate is placed on a recessed bearing in the frame, which ensures precise positioning.

Can only be used with ClassicLine frame.

Beklager, men "Kombinippel purus 64/58-50/40" virker ikke å være et ord eller uttrykk på noen språk. Det kan være en teknisk term eller produktnavn som krever mer kontekst for å oversettes nøyaktig.

PURUS gummiforbindelse Ø75 / 50-5040mm TPE-gummi, brukt som elastisk tetning ved overgang fra en dimensjon til en annen, godkjent for horisontal og stående montering og installasjon, typegodkjent

The set consists of a panel, rail, heightener set and screws. The set must be assembled before installation.

Includes 2 x hooks to be used for lifting the panel.

The panel solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit. Installed with HighLine frame.

The heightener set to adjust the panel is included, so that the panel can be matched to the frame height.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Can be freely positioned against the back wall, independent of any side walls. The rear flange has been moved 12 mm backwards, to fit 15 -20mm wall tiles + tile mortar + wetroom membrane.

NB! ClassicLine or HighLine frame must be used.

ShowerLine has a built-in slope, so that the floor in the shower cubicle slopes correctly by 2% down towards the floor drain. For added wetroom safety, the shower cubicle is framed by flanges on three sides.

The shower screen is mounted in the track on the fixed module, to eliminate the risk of working loose over time.

Combine with: Outlet unit, frame, grating/panel and shower screen.

Can be freely positioned against the back wall, independent of any side walls. The rear flange has been moved 12 mm backwards, to fit 15 -20mm wall tiles + tile mortar + wetroom membrane.

NB! ClassicLine or HighLine frame must be used.

Can be freely positioned against the back wall, independent of any side walls.

The drain unit has one wall flange.

With side drain on the left.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

The grate is placed on a recessed bearing in the frame, which ensures precise positioning.

Can only be used with ClassicLine frame.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

ShowerLine has a built-in slope, so that the floor in the shower cubicle slopes correctly by 2% down towards the floor drain. For added wetroom safety, the shower cubicle is framed by flanges on three sides.

The shower screen is mounted in the track on the fixed module, to eliminate the risk of working loose over time.

Combine with: Outlet unit, frame, grating/panel and shower screen.

Can be freely positioned against the back wall, independent of any side walls. The rear flange has been moved 12 mm backwards, to fit 15 -20mm wall tiles + tile mortar + wetroom membrane.

NB! ClassicLine or HighLine frame must be used.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

The grate is placed on a recessed bearing in the frame, which ensures precise positioning.

Can only be used with ClassicLine frame.

ShowerLine has a built-in slope, so that the floor in the shower cubicle slopes correctly by 2% down towards the floor drain. For added wetroom safety, the shower cubicle is framed by flanges on three sides.

The shower screen is mounted in the track on the fixed module, to eliminate the risk of working loose over time. Combine with: outlet unit, frame, grating/panel and shower screen.