Dreneringsprodukter - side 21

AMAX Pro er en avløp i PP for dreneringssystemer i bygninger for transport av kloakk.

dBlue er en avløpsrør i PP (polypropylen) i 3 lag. Det egner seg for installasjon på steder der det er krav til støynivået. Rørsystemet har dokumentert lydnivå på 19 dB (A). Hvis det er strengere krav til lyd, anbefaler vi FRIAPHON.

AMAX Pro er en avløp i PP for dreneringssystemer i bygninger for transport av kloakk.

Geberit Pluvia bladfangst

For bygningsdrenering, for områdedrenering

Biter av PEH for sveising, brukes til avløpsinstallasjoner. Med TPE lyddemping.

Tilbehør til avløpsrør og lister av PEH for sveising, brukes til avløpsinstallasjoner. Med TPE lyddemping.

Biter av PEH for sveising, brukes til avløpsinstallasjoner. Med TPE lyddemping.

Geberit PE grenrørsbeslag 45°: d=40mm, d1=40mm

For bygningsdrenering, for områdedrenering

Biter av PEH for sveising, brukes til avløpsinstallasjoner. Med TPE lyddemping.

For bygningsdrenering, for områdedrenering

Tilbehør til PEH avløpsrør for sveising: Med 2 posisjoner. for vanlig og fast punktsuspensjon.

Biter av PEH for sveising, brukes til avløpsinstallasjoner. Med TPE lyddemping.

•For anchor-point fastening of pipes in combination with electrofusion tapes•For anchor-point fastening of pipes in combination with electrofusion couplings•For sliding bracket fastening of pipes•For fastening with tension wedges•For fastening to Geberit Pluvia support rails with square profile

Geberit rørbrakett med gjengehylse M8 / M10: di = 110mm

With side drain on the right.

Can be freely positioned against the back wall, independent of any side walls. Only for use with ClassicLine.

Water trap for corner outlet houses 2001.

The set consists of a panel, rail, heightener set and screws. The set must be assembled before installation.

Includes 2 x hooks to be used for lifting the panel.

The panel solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit. Installed with HighLine frame.

The heightener set to adjust the panel is included, so that the panel can be matched to the frame height.

NB: PVD-treated surface.

The set consists of a cassette, rail, heightener set and screws. The set must be assembled before installation. Available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile). Supplement cassette with your own material (e.g. matching floor tile), to complete the solution. The cassette solution is placed directly inside the drain unit. The rail is specially designed to provide a snug fit.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile).

The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.

The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

The grating is selected from among six attractive designs.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

Choose between two models. A panel completely without frame, or the model with panel including frame.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.