Alu pex-systemer - side 4

Geberit Mepla T-stykke, redusert: d=50mm, d1=32mm, d2=50mm

Geberit Mepla-adapter til Geberit Mapress, med glatt ende: CC499K, d=40mm, d1=35mm

Raxofix T-stykke med SC-Contur-silisiumbronse-trykkontakter d1: 40, d2: 32, d3: 40

Henco 16 mm x 34 PVDF trykk til eurocone for vann-, varme- og kjøleanlegg. Maks. 16 bar.

Messing trykk-kobling med en korrosjonsbestandig overflate med rustfritt stål presslokk for varmtvann og radiator systemer, stoppring, trykkindikator, fargekode, garantert lekkasje hvis ikke presset. Kalibreringsfri. Sylindrisk utvendig gjenge i henhold til EN 10226-1 for pakning. Kun til bruk med Uponor MLC-, Uni Pipe Plus- og Metallic Pipe Plus-rør og med Uponor godkjent pressverktøy.

Raxofix T-piece with SC-Contur- silicium bronze- press connectorsd1: 25, d2: 20, d3: 20

Raxofix Adapter with SC-Contur- silicium bronze- press connection, R-threadd: 25, R: 1

Raxofix Adapter with SC-Contur- silicium bronze- press connection, R-threadd: 25, R: 34

Geberit Mepla T-stykke, redusert: d=26mm, d1=16mm, d2=26mm

Raxofix T-stykke med SC-Contur- silisiumbronse-trykkontakter d1: 20, d2: 16, d3: 20

Henco bøye verktøy for Ø20 mm alu pex

Geberit Mepla T-stykke, redusert: d=32mm, d1=26mm, d2=32mm

Raxofix Adapter with SC-Contur- for all Viega metallic systems- silicium bronze- press connectorsComponentsEPDM sealing elementd1: 20, d2: 15

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

For-kobling PPSU Uponor 50X32 mm

Geberit Mepla albue: 90°, d=32mm

Geberit Mepla albue: 90°, d=20mm

Raxofix Adapter with SC-Contur- for all Viega metallic systems- silicium bronze- press connectorsComponentsEPDM sealing elementd1: 16, d2: 15

Uponor 1029137 VVS-kobling Kranadapter

Used with Roth alu-laserplus pipe and Roth tools

Raxofix Adapter elbow 90° with SC-Contur- silicium bronze- press connection, R-threadd: 16, R: 34

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Henco 40 x 40 mm PVDF trykkbøyd 90° for vann-, varme- og kjøleanlegg. Maks. 16 bar.

Geberit Mepla-adapter med kvinnelig gjenge: d=26mm, Rp=1

Kalibreringsverktøy HENCO (Kalispeed), 20 mm