Alu pex-systemer - side 11

Uponor 1046901 VVS-kobling Kranadapter

Used with Roth alu-laserplus pipe and Roth tools

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Raxofix T-piece with SC-Contur- silicium bronze- press connectorsd1: 25, d2: 20, d3: 20

Raxofix Adapter elbow 90° with SC-Contur- silicium bronze- press connection, R-threadd: 16, R: 34

Raxofix T-piece with SC-Contur- silicium bronze- press connectorsd1: 32, d2: 25, d3: 32

Raxofix Adapter with SC-Contur- silicium bronze- press connection, Rp-threadd: 20, Rp: 12

Raxofix Adapter with SC-Contur- silicium bronze- press connection, R-threadd: 25, R: 1

Raxofix Adapter with SC-Contur- silicium bronze- press connection, R-threadd: 32, R: 1

Raxofix Connection screw fitting with SC-Contur- silicium bronze- press connection, G-thread- flat sealingComponentsEPDM sealing elementd: 20, G: 34

Used with Roth alu-laserplus pipe and Roth tools

Uponor 1070502 VVS-kobling Kranadapter

Used with Roth alu-laserplus pipe and Roth tools

Trykk-kobling Uponor med pakninghylse/hylse 16X3/4

Used with Roth alu-laserplus pipe and Roth tools

Used with Roth alu-laserplus pipe and Roth tools

Used with Roth alu-laserplus pipe and Roth tools

Raxofix Coupling with SC-Contur- silicium bronze- press connectiond1: 32, d2: 25

Raxofix kobling med SC-Contur - silisiumbronse - trykktilkobling d1: 20, d2: 20

Raxofix T-piece with SC-Contur- silicium bronze- press connectorsd1: 25, d2: 16, d3: 16

Raxofix kobling med SC-Contur - silisiumbronse - pressetilkobling d1: 40, d2: 40

Raxofix Adapter elbow 90° with SC-Contur- silicium bronze- press connection, R-threadd: 32, R: 1

Raxofix T-stykke med SC-Contur-silisiumbronse-trykkontakter d1: 40, d2: 32, d3: 40

Raxofix T-piece with SC-Contur- silicium bronze- press connectorsd1: 25, d2: 16, d3: 25

Raxofix Adapter with SC-Contur- silicium bronze- press connection, Rp-threadd: 25, Rp: 34